bonjour ,voila j'ai un probleme que je n'arrive pas a resoudre.
je viens de recuperer un ordi ,il marche mais a condition que je fasse un clear cmos avant que je l'allume ,si je ne le fais pas l'odi ne s'allume pas c'est a dire que je n'ai aucun bip et juste le ventilo du cpu qui tourne.
j'ai teste avec 2 alim differente ( seasonic 300fs et une noname de 360w) ,2 barrettes de ram differente ( 1go samsung ddr pc3200 ,256 mo spectek ddr pc2700) ,avec ou sans disque dur ,et 2 cartes graphiques differentes (geforce 5200fx ,riva tnt2). j'ai meme change la pile cmos et toujours le meme probleme.
une idee ? merci
config :
amx athlon xp 1800+
msi ms-6382 v2
Essaie de MAJ son BIOS ... c'est bizarre en effet.
__________________ Hello IT ... Have you tried to turn it off and on again ? ... The button on the side, is it glowing ? ... Yeah you need to turn it on ! ... The button turns it on ? ... You DO know how a button works don't you ! ?
voila j'ai telecharge le bios j'ai lu la doc mais a partir de l'etape 5 j'ai du mal a comprendre ,si quelqu'un pourrai m'aider. merci.
Code:
Special Note:
The BIOS and DEVICE DRIVERS contained here are exclusively for Micro-Star products only. Micro-Star assumes no responsibility for any damages resulting from improper use or lack of technical expertise.
WARNING!!!!!
DON'T FLASH FROM A FLOPPY DISK!!!!
DON'T FLASH WHEN YOUR SYSTEM IS RUNNING FINE!!!!
DON'T FLASH IF YOU DON'T KNOW WHAT YOU ARE DOING!!!!
Award BIOS Flash Procedure
(Special Thanks to Forum Moderator Bas for his valuable contribution)
1. Check your BIOS for BIOS FLASH DISABLED and ENABLE it, some boards have this function.
For Example:
K7N420 Pro (MS-6373) – BIOS setup/Integrated Peripherals/BIOS Protect/Disabled
2. Know Your model number
a. Open your case and look for the MS-XXXX number on the motherboard between the PCI slots, also check the version number that is written there as well. (some motherboards are named like K7T Turbo, make sure you have the right version number)
b. Boot up your system & take a look at the top left screen during POST, you should see something like “W6373MS v2.1 122101” This means the board is MS-6373 with BIOS version 2.1
Hint: Many systems are clearing this message very fast, the bios version is then unreadable, you can either press “PAUSE” or disable the “Quick Boot” in the BIOS setup.
3. Download the BIOS that matches your motherboard AND version number (some motherboards are named like K7T Turbo, make sure you have the right version number). BIOS can be found according to the CPU type of your board like if your CPU is Intel P4 478 type then look here
MSI -- MICRO-STAR INT'L CO.,LTD.
if you cannot find the BIOS that matches your board, try here MSI -- MICRO-STAR INT'L CO.,LTD.
4. Extract the BIOS-archive that you have downloaded by double clicking to c:\test
5. Boot your system from a Win98 or WinME boot-floppy.
How to make boot floppy in case your don’t have it ready:
For Win9X, You can type [C:\ format a:/s] from the DOS prompt.
For WinMe, You can make a boot floppy from control panel--> add/remove program-->make boot floppy. Remove autoexec.bat & config.sys file if there's any.
For Win2000, there's no way to make boot floppy, so you have to either use Win9X or WinME boot floppy.
For WinXP, you can make a DOS boot disk. Go to Your Computer, right click drive A:, select Format, select copy system files.
7. When you get the A:\ prompt, type the following sequence:
C: <enter>
cd\test <enter>
C:\test> awdfl783m BIOS file
(to save or not to save old BIOS is the user’s decision)
8. Reboot your system when prompted
P.S. If your system doesn't boot after you flashed, please refer to the BIOS recovery method as described MSI -- MICRO-STAR INT'L CO.,LTD.
car il existe 2 version la version 1 et la version 2 .
Théoriquement oui. Mais je dis ça, je dis rien.
6382 rev 2.0 BIOS 3.1.
EDIT: Place W6382VMS.310 et AWFL816A à la racine de ton C.
Là-> C:\
Crée une disquette de boot via XP. Insère une disquette->Formater->Disquette de démarrage...
Boote dessus.
Tape C:\
Entrée
Puis AWFL816A W6382VMS.310
Entrée
Dernière modification par kira ; 24/03/2008 à 18h56.
Théoriquement oui. Mais je dis ça, je dis rien.
6382 rev 2.0 BIOS 3.1.
EDIT: Place W6382VMS.310 et AWFL816A à la racine de ton C.
Là-> C:\
Crée une disquette de boot via XP. Insère une disquette->Formater->Disquette de démarrage...
Boote dessus.
Tape C:\
Entrée
Puis AWFL816A W6382VMS.310
Entrée
merci pour ta reponse mais comment fait on quand on a pas de lecteur disquette?
merci.
probleme bizzare
Mode linéaire
